Συσκευές ελέγχου - CR25-100 -CR25 CR Series Brass Pressure Relief Valve, 0-100 psi Ρυθμιζόμενο εύρος πίεσης, 1/4 Αρσενικό NPT

Brand:Control Devices

3.6/5

Ft
43.20

Αυτή η βαλβίδα εκτόνωσης πίεσης CR25-100 του Control Devices διαθέτει ορειχάλκινο σώμα, ρυθμιζόμενη πίεση εκτόνωσης, σύνδεση εισόδου με σπείρωμα αρσενικού NPT 1/4 και δακτύλιο Ο φθοράνθρακα. Το ορειχάλκινο σώμα της βαλβίδας, η ορειχάλκινη έδρα της βαλβίδας και το κάλυμμα από ανοξείδωτο χάλυβα αντιστέκονται στη διάβρωση και μπορούν να χρησιμοποιηθούν σε θερμοκρασίες λειτουργίας έως 250 βαθμούς F. Η βαλβίδα μπορεί να ρυθμιστεί ώστε να ανοίγει μεταξύ 0 και 100 psi χρησιμοποιώντας το πόμολο νάιλον τύπου μικρομέτρου. Αυτή η βαλβίδα ασφαλείας έχει τυπική ταχύτητα ροής 6 κυβικά πόδια ανά λεπτό (SCFM) και είναι κατάλληλη για εφαρμογές εκτόνωσης πίεσης χαμηλής ροής, όπως σε αεροσυμπιεστές χωρίς δεξαμενή. Οι βαλβίδες εκτόνωσης αφαιρούν την υπερβολική πίεση ή το κενό από ένα σύστημα. Τα ανοίγματα των βαλβίδων επιτρέπουν σε υγρά ή αέρια να διαφύγουν για να μειώσουν την πίεση και στη συνέχεια κλείνουν μόλις η βαλβίδα φτάσει στο όριο πίεσης επανατοποθέτησης. Ανακουφίζουν επίσης το υπερβολικό κενό ανοίγοντας για να απελευθερώσει ένα αέριο στο σύστημα και στη συνέχεια κλείνοντας αφού φτάσει στο όριο χαμηλής πίεσης. Ορισμένες ανακουφιστικές βαλβίδες διαθέτουν μηχανισμό ρύθμισης για τη ρύθμιση της πίεσης στο σημείο που ανοίγει η βαλβίδα, καθιστώντας την κατάλληλη για διάφορες εφαρμογές. Οι ανακουφιστικές βαλβίδες βαθμολογούνται ανάλογα με τον όγκο υγρού ή αερίου που μπορεί να ρέει μέσα από αυτές και το υλικό από το οποίο κατασκευάζεται η βαλβίδα πρέπει να είναι κατάλληλο για το ρευστό ή το αέριο, το οποίο μπορεί να είναι διαβρωτικό ή σε ακραία θερμοκρασία, στο οποίο λειτουργεί. Οι βαλβίδες εκτόνωσης χρησιμοποιούνται σε ποικίλες εφαρμογές, όπως αεροσυμπιεστές, πετροχημική και χημική κατασκευή, επεξεργασία φυσικού αερίου και παραγωγή ενέργειας. Η Control Devices κατασκευάζει βαλβίδες και άλλες συσκευές ελέγχου ροής. Η εταιρεία, που ιδρύθηκε το 1963, έχει την έδρα της στο Fenton, MO.

Νάιλον πόμολο μικρομέτρου για ρύθμιση ανακούφισης πίεσης. Ο δακτύλιος σιλικόνης παρέχει στεγανή στεγανοποίηση εντός 10 τοις εκατό της καθορισμένης πίεσης. Ορειχάλκινη κατασκευή και ανοξείδωτο ελατήριο για αντοχή στη διάβρωση. 1/4 αρσενική σύνδεση εισόδου με σπείρωμα NPT. Ρυθμιζόμενη πίεση εκτόνωσης από 0 έως 100 psi.
Brand Control Devices
Country of Origin USA
Domestic Shipping Item can be shipped within U.S.
Exterior Finish Stainless Steel
Inlet Connection Size 0.25 Inches
Inlet Connection Type National Pipe Tapered
International Shipping This item can be shipped to select countries outside of the U.S.
Is Discontinued By Manufacturer No
Item model number CR25-100
Manufacturer Control Devices
Material Brass
Outlet Connection Type MNPT
Package Dimensions 4.33 x 3.23 x 1.69 inches; 2.4 Ounces

3.6

8 Review
5 Star
71
4 Star
16
3 Star
8
2 Star
3
1 Star
3

Γράψτε την κριτική σας

Το email σας δεν θα δημοσιευτεί. Όλα τα υποχρεωτικά πεδία επισημαίνονται με*

Scritto da: Mac
1 year of use and still good
I bought this to install on my steam sterilizer. The sterilizer reaches 121°C (250°F) and 15-18psi. I obviously have an additional safety release valve and a pressure gauge. The markings on the adjustable valve seem to be within the stated tolerance. It does occasionally get stuck closed. I learned it is best if I open it completely to vent before building pressure and then adjust it when the desired pressure is reached to allow very minimal venting. It never gets stuck if this is done. It always closes and does hold a vacuum upon cooling. All in all it does exactly what I want. I may replace it soon with the same valve simply because it is cheap and for peace of mind. 4/5 for overall quality 5/5 for quality at low price
Scritto da: Caitlin G
Good as a PRV
I’m using this PRV as part of a pressure fermentation and spunding rig. For my use it works really well with one exception. It needs to be used with a pressure gauge since the gauge on the pressure adjustment is 10-15 psi off. 10 psi on the PRV is actually 15 psi on a gauge.
Scritto da: Janice Villanueva
it works pretty cool so far for what I use it for
It relieves a fair amount of pressure. I believe more expensive valves relieve more pressure if that is what you need. Overall, it works pretty cool so far for what I use it for. Ignore the numbers used for measuring on this item. It's only there to make the item more attractive to buy. I had to buy a nut for mine in order to install it, which wasn't very hard. I use mine along with a pressure gauge on a homemade low pressure 55 gal steel sterilizing/pasteurizing drum. I never allow the tank to exceed 2 psi. I use this item basically to begin relieving pressure when the pressure reaches 1-1.5 psi. I adjust it according to my pressure gauge. It is most useful to me really in that it is an alarm for me to turn the propane down or open more wide the main relief valve. And I'm sure it helps prevent the psi from exceeding the point that it is set at. I do believe that if I turned the propane all the way up that this pressure relief valve would not be able to prevent my tank from exceeding the 2 psi that I am able to set it at. This is not a proven fact because I have not tested it. I'm just judging by the amount of pressure that this valve actually relieves. It relieves enough pressure that I don't try to find a better relief valve. But if I wanted to be perfectly safe i would wish for a valve that relieves more pressure so that to be sure that it would be impossible to exceed the 2 psi mark that I can set it at using this valve.
Scritto da: Book Lover
Seems to work great! I had it set at 75, and it didn't leak at 50PSI.
Seems to work great! I had it set at 75, and it didn't leak at 50PSI. The spring loaded design looks like this design should be fairly robust and fool proof. I heard that it leaked for some people, but my application didn't. I used thread tape and never opened it all the way up, so it seems to work for me.
Scritto da: D. Morrison
Leaking Valve FIXED
Like others, my PRV developed a leak out of nowhere (it would never fully close). I removed it from the fitting and found that a small piece of thread tape had become trapped in the valve seat, causing the leak. After removing this and reassembling, the leak is gone and the valve operates properly. I would be cautious using this in a setup where any debris could enter the valve. The markings are wildly wrong, but with a gauge in the system this is easily set to low pressure (10 PSI). I do not know if it would work toward the higher end of the rated range.
Scritto da: V. Williams
Tested positive for lead content
This device seems well made and durable, but if you are intending to attach it to a beverage line or passing liquid near it that is intended for consumption, think twice. Having read about various factories mixing lead in their brass, I decided to buy a reliable lead testing kit and tested all my recent brass connector purchases. Four out of 16 items tested positive for lead content. This item was one with lead in it. Photo provided with a sample of many items I tested.
Scritto da: David Swift
Excellent piece of hardware
Bought for a safety valve on a science project. Nice fine adjustment. Doesn't leak until set point is hit. Closes tight when pressure goes below set point. Tested with some pretty fast transients and it worked great. Could have done without the factory installed thread sealant.
Scritto da: Alex
Does the Job
I use it as an emergency air pressure release to bleed off back pressure from my Medo LA45C pump for my guppies LOL. Set it to open at 1.5 PSI I actually dump excess air through a ball valve and huge 1/5" x 8" airstones so my backpressure on the ball valve is set to 0.5PSI . but if airstones plug up this valve opens to keep back pressure from blowing my piston rings on the Medo.

Σχετικά προϊόντα

Ανακαλύψτε το διεθνές μας δίκτυο

Στέλνουμε σε 28 χώρες, πάνω από 200.000 προϊόντα. Μείνετε ενημερωμένοι, εγγραφείτε στο ενημερωτικό δελτίο.

Array