HHIP 3903-1600 Er-32 Indexing Spin Jig με γαλλικό κλειδί

Brand:HHIP

3/5

Ft
236.79

HHIP ER-32 Indexing spin jig με κλειδί. Αυτό το εξάρτημα ευρετηρίασης και λείανσης χρησιμοποιεί κολέτες ER-32 (εύρος 1/16. 13/16) για καλύτερο κράτημα και ακρίβεια. Επεκτείνει τις δυνατότητες των πρέσων τρυπανιών, των επιφανειακών μύλοι, των μηχανών κοπής γραναζιών και των φρέζας. Ο άξονας σκληρύνθηκε και αλέστηκε με α.0005 T.I.R. 10 τρύπες βερνιέρου για ευρετηρίαση 1°. Διαδρομή 2 αξόνων για λείανση φλάουτου. Η πλάκα δείκτη διαμέτρου 5 έχει κύκλο 36 οπών και βαθμολογείται από 0 έως 35 για άμεση ευρετηρίαση σε βήματα 10° και σημειώνεται σε βήματα των 5°. Κλείδωμα ατράκτου για σύσφιξη κολέτας. Το ύψος του κέντρου είναι 2,75. Το αποτύπωμα βάσης είναι 4,5 Χ 4. Γείωση παράλληλη προς τον άξονα.

Διαδρομή 2 αξόνων για λείανση φλάουτου. 10 τρύπες βερνιέρου για ευρετηρίαση 1°. Ο άξονας σκληρύνθηκε και αλέστηκε με .0005 T.I.R. Επεκτείνει τις δυνατότητες των πρέσων τρυπανιών, των επιφανειακών μύλοι, των μηχανών κοπής γραναζιών και των φρέζας. Αυτό το εξάρτημα ευρετηρίασης και λείανσης χρησιμοποιεί κολέτες er-32 (εύρος 1/16~13/16) για καλύτερο κράτημα και ακρίβεια.
Brand HHIP
Country of Origin China
Cut Type Center Cutting
End Cut Type Center
Item Dimensions LxWxH 9 x 6 x 5 inches
Item model number 3903-1600
Manufacturer HHIP
Product Dimensions 9 x 6 x 5 inches; 13.35 Pounds

3

5 Review
5 Star
38
4 Star
25
3 Star
36
2 Star
0
1 Star
0

Γράψτε την κριτική σας

Το email σας δεν θα δημοσιευτεί. Όλα τα υποχρεωτικά πεδία επισημαίνονται με*

Scritto da: Hobby Machinist
Getting a Handle on It
The main problem I had was that the handle for the spindle crank was missing. I carefully rechecked the packaging, but it was nowhere to be found. Fortunately, I'm a hobby machinist, so I was able to manufacture a replacement handle on my lathe from some scrap steel and aluminum round stock (see photos 1-3). For those who have a similar problem, the threads where the handle attaches to the spindle crank is M6, 1.0, so you'll need a set of metric threading dies to thread the new handle pin. Even with a proper handle, the spindle was very difficult to turn. Based on past experience with Chinese-made equipment, I suspected that the problem due to dirt and grinding dust in the spindle. I disassembled the spindle and cleaned the spindle body and shaft with WD-40 and shop towels (see photo 4). I oiled the spindle with way oil, reassembled it, and it now turns smoothly. Other than this I was satisfied.
Scritto da: nicholas breitling
There was a little bit of clean up.
I did have to take it apart as others mentioned, and the runout is as advertised. However, this purchase was with the understanding of there being a 5C under the ER32 according to the reviews. I have been unable to remove the ER32 adapter if any. If someone could direct me into how it was removed it would be much appreciated. But the indexer is as advertised and has worked very well. 3 stars for the indexer. Deburring cleaning and Amazon's amazing packaging service is another star off. But will update if I have any luck with removing the adapter. I would recommend this.
Scritto da: Carl Riemann
Not blue as pictured, but functional nonetheless
I am modifying my spindexer to hold endmills while sharpening them. I think it will work well once I am finished.
Scritto da: karl hoffman
As expected from China
Standard item from China. Needs cleaned thoroughly. The run out was as advertised .0005. (After cleaning) All of the flat surfaces are incredibly rough and I will have to re-grind them. They seem to be flat though. This is a standard indexer with a ER 32 adapter there is a 5C taper under it
Scritto da: Amazon Customer
Decent product. Good value for the price.
Good product. Nice to be able to use 5c collets as well as er32. Has slight runout. About one thousandth but should be acceptable for what I’m using it for.

Σχετικά προϊόντα

Ανακαλύψτε το διεθνές μας δίκτυο

Στέλνουμε σε 28 χώρες, πάνω από 200.000 προϊόντα. Μείνετε ενημερωμένοι, εγγραφείτε στο ενημερωτικό δελτίο.

Array