DROK® LM2596 Μετατροπέας αναλογικού ελέγχου Buck DC-DC Βαθμιαία μονάδα ρυθμιστή τάσης μετασχηματιστή 36V 24V 12V σε 5V 2A Σταθεροποιητής βολτ μετατροπέα ισχύος με κόκκινη οθόνη LED Τάση εισόδου/εξόδου πλακέτας βολτόμετρου

Brand:DROK

3.2/5

Ft
31.40

Παράμετροι: Τάση εισόδου: DC 4~40V (η τάση εισόδου θα πρέπει να είναι υψηλότερη από την τάση εξόδου τουλάχιστον 1V) Τάση εξόδου: DC 1,25~37V (συνεχώς ρυθμιζόμενο) Ρεύμα εξόδου: 2A (για σταθερή λειτουργία), 3A max. Βολτόμετρο: 0~40V Ακρίβεια βολτόμετρου: .+/-0,1V Συχνότητα εσωτερικής ταλάντωσης: 150KHz Υπάρχει μεγάλη περιοχή χαλκού στην πλάτη του για ενίσχυση της απαγωγής θερμότητας Πώς να ρυθμίσετε την ακρίβεια του βολτ εισόδου/εξόδου; (1) Βαθμονόμηση τάσης εξόδου Αρχικά, ρυθμίστε το δεξί κουμπί έτσι ώστε το LED OUT να ανάβει, το βολτόμετρο να δείχνει την τιμή της τάσης εξόδου. Πατήστε το δεξί κουμπί για περισσότερο από 2 δευτερόλεπτα, αφήστε το, το βολτόμετρο και η λυχνία LED OUT αναβοσβήνουν σε συγχρονισμό, ώστε να μπείτε στη λειτουργία βαθμονόμησης τάσης εξόδου. Δεύτερον, πατήστε το δεξί κουμπί (κανονική ταχύτητα), η τιμή της τάσης αθροίζει μια μονάδα. Πατήστε το αριστερό κουμπί, μείον μια μονάδα. Επειδή μια μονάδα είναι μικρότερη από 0,1 V, η ελάχιστη τάση εμφανίζεται στα 0,1 V, επομένως πρέπει να πατάτε συνεχώς 1-5 φορές για να δείτε το βολτόμετρο να αλλάζει 0,1 V, πόσες φορές το βολτόμετρο αλλάζει 0,1 V πατώντας το πλήκτρο, ανάλογα με η τρέχουσα τάση οθόνης, όσο υψηλότερη είναι η τάση, τόσο λιγότερος είναι ο αριθμός των πιέσεων. Τρίτον, πατήστε το δεξί κουμπί για περισσότερα από 2 δευτερόλεπτα, αφήστε το, για έξοδο από τη λειτουργία βαθμονόμησης τάσης εξόδου. Όλες οι παράμετροι έχουν ρυθμιστεί σε αυτόματη απενεργοποίηση για αποθήκευση. (2) Βαθμονόμηση τάσης εισόδου Αρχικά, ρυθμίστε το δεξί κουμπί έτσι ώστε να ανάβει η λυχνία IN, το βολτόμετρο να δείχνει την τιμή της τάσης εισόδου. πατήστε το δεξί κουμπί για περισσότερα από 2 δευτερόλεπτα, αφήστε το, το βολτόμετρο και η λυχνία LED IN αναβοσβήνουν σε συγχρονισμό, ώστε να μπείτε στη λειτουργία βαθμονόμησης τάσης εισόδου. Τα βήματα 2 και το βήμα 3 είναι σύμφωνα με τη μέθοδο βαθμονόμησης της τάσης εξόδου.

Πατήστε το κουμπί για 1 έως 4 δευτερόλεπτα, το βολτόμετρο θα απενεργοποιηθεί όταν αφήνετε τα χέρια σας. το βολτόμετρο είναι πολύ ακριβές. Με λειτουργία βαθμονόμησης σφάλματος μέτρησης τάσης εισόδου και εξόδου. Οι ακροδέκτες καλωδίωσης δεν απαιτούν συγκολλητικό σίδερο και δημιουργούν βολική χρήση. Πατήστε το κουμπί δίπλα στο βολτόμετρο για να ελέγξετε την τάση εισόδου ή την τάση εξόδου. Οι πράσινες λυχνίες LED ανάβουν κατά τον έλεγχο της τάσης εξόδου. Η κόκκινη λυχνία LED ανάβει κατά τον έλεγχο της τάσης εισόδου. Έχει πολύ σταθερή έξοδο, το εύρος εισόδου είναι DC 4~40V και το εύρος εξόδου είναι DC 1,25~37V, βεβαιωθείτε ότι η τάση εισόδου πρέπει να είναι υψηλότερη από την τάση εξόδου τουλάχιστον 1V. Μπορεί να χρησιμοποιηθεί για πολλά ηλεκτρονικά έργα. Αναλογικός έλεγχος: χρησιμοποιώντας ένα μίνι κατσαβίδι για να αυξήσετε ή να μειώσετε την τάση εξόδου ρυθμίζοντας τη βίδα, δεξιόστροφα για να αυξήσετε την τάση και αριστερόστροφα για να μειώσετε την τάση.
Brand DROK
Country of Origin China
Current Rating 3 Amps, 2 Amps
Is Discontinued By Manufacturer No
Item model number 090118
Item Weight 0.02 Pounds
Manufacturer DROK
Package Dimensions 5.24 x 2.48 x 1.42 inches; 0.32 Ounces

3.2

12 Review
5 Star
62
4 Star
15
3 Star
7
2 Star
4
1 Star
12

Γράψτε την κριτική σας

Το email σας δεν θα δημοσιευτεί. Όλα τα υποχρεωτικά πεδία επισημαίνονται με*

Scritto da: Wino
Typical DROK quality. well packaged. Great value.
I've used DROK to put usb charger ports in boats, bikes, house lamps and a car. The house lamp was the hardest; I used a power brick laying around, but fit was an issue. We added a 24x7 power port to a BMW whose 'smart bus' seemed designed to drain the batteries of all non-BMW branded devices. Wired directly off the battery to a DROK converter supplied port laying inside the (armrest) bin.. problem solved. The owner leaves his cellphone in the vehicle and uses the bluetooth link to the house phone. And the Buck converter, what I've noticed, at full charge it gets pretty warm, too warm to poke around with your finger checking how hot it is... so I added a heatsink to the chip and venting to the case. Supplying about 10W flat out, it is way cooler than I'd have believed. At maintenance charge it is essentially warm. These things are efficient! I don't notice a difference on my trike after a week leaving the power on to the (turned off) LED lighting. On bikes and boats worry about ventilation and waterproofing, as in both places nobody remembers to charge devices until they really need power. I've put in 5 of these and made portables for friends who want to be able to plug into 12v ports. We have yet to get a failure other than when I connected it so sadly wrong. I like the display because to me it's worth the price to be able to verify performance. It also means I can leave my DVM packed. The display is certainly accurate for its use, maybe 0.1V or so, and you can calibrate it if you want to feel better. This is not a laboratory supply; you don't get that for $10. I'm very happy with the value. In fact I worry a bit about the cutthroat Chinese business model. If they can resist the plunge to the bottom on pricing, certainly DROK could be another name like Westinghouse (etc.). It can take a while to get the order. I usually get it within 10 days or so, which is astonishing. Then (likely customs) happens, and it takes weeks. DROK supplier can hardly affect that, so be patient. A part order from Detroit to Louisville could take 5 days not that long ago.
Scritto da: TheBreadFamily
Great device
Used this in my ender 5 plus to power a new fan. New fan was 12 v this took 24 v and dropped it to 12 with adjustments.
Scritto da: heuristik
and was sure until today the potentiometer was bad. I couldn't get the output voltage to change
I've had the unit for a couple of weeks, and was sure until today the potentiometer was bad. I couldn't get the output voltage to change, no matter what combination of buttons and cranks on the dial I tried. Revisited the product page, thankfully the description is more helpful than I recalled. But in case you're having similar troubles, you might find these tips helpful: 1) If you are working with low voltage input, >12V for example, before you do anything else, turn the pot dial 10-12 times counter clockwise (use the little brass screw at the top, right from middle of the unit.) 2) Two buttons on this device as opposed to many of the similar types of buck converters available. This provides a different method for changing voltage, as a result. Flip the red light to the Out (right) side, hold the right button down for 2 seconds then release. The displayed voltage should be blinking. Now, the left button will reduce, the right button will increase the Output voltage. Note one click doesn't always change the display, though if you are connected to your multimeter you will notice it does indeed change the voltage... The sensitivity is a bit unpredictable, but just click-click-click to get to your intended value, eventually you'll reach it. 3) If you are dealing with very sensitive voltage level requirements, consider pre-setting the device for the intended values and then turning off the display by clicking the left button. The unit will save the values you set even after removing its power source. Thus far, been pleased (now that I know how to use it) with the results.
Scritto da: Rob
Seems stable
It didn't work for the first project I tried it on, stepping from 24V down to 5 was too much for it and it would overheat - even with a low amp load. Now using it to drop 9V down to 5 and it works great even with more load than before.
Scritto da: MadMatt
Reduced current at lower volts, but still great.
This is for the LM2596 step down DC to DC voltage converter with the LED display. Not for an adjustable current device. I purchased this device to drive glow heads on an old Cox glow engine that I was given. I use a 12V 5Ah SLA battery and intended to run this a 1.5V to light the glow head element. I found that it could only source about 1.75A at 1.5V, but I could increase the voltage until I got 2.5 to 3A through the glow head and it worked fine. This was at about 2.8V on the voltage display, which I did calibrate. I contacted DROK to ask about this performance and they confirmed that you can't get the full 3A rating at this low of a voltage. I don't mind running higher voltage as I just need a certain current to light the glow plug. But I though I would leave this information in case it helps someone else. A knowledgeable electrical person might have anticipated this performance, but it was a surprise to me. The product works well for me, seems well-assembled, and DROK customer service was prompt and knowledgeable. No complaints.
Scritto da: ben
Test them first with an inline fuse.
Make sure you bench test these before you install on anything important. 1 worked no issues the other had some sort of direct short after the cap and let all of the smoke out instantly. The one that does work works perfect and has been running for days nonstop controlling a small fan.
Scritto da: L. Mims
very pleased with this device
I'll upgrade my 4 star to 5 stars after a few months of use to make sure it works, but honestly this thing worked right off the bat, no problems. Checked against my multimeter, and the 24DC in comes out a smooth 11.96 (12DC) out. Even when the input jumps a little, the output is really solid, very pleased with this device. I'm using it to power a 12v CPU fan I'm using for cooling in a homemade audio amplifier. The amp runs on 24v so I needed to step down for the CPU fan.
Scritto da: Andy Bobandy
Works as Intended
There are cheaper options out there in bundles of mass production, however this one attracted me because of the voltage display on board - and its accurate. I took my voltmeter to the output end and the difference between my voltmeter and the onboard display was .02. Used this in my 3d printer to step down the voltage for my LED lights. Will buy more in the future as I build an enclosure, and I'll most likely stick to these if I add lights. If you plan on using a buck converter to step down voltage for Noctua fans on your 3D Printer, I suggest the bulk ones as they're smaller and will take up less room if you hide them with the motherboard, like on my Ender 3 V2.
Scritto da: Richard
Worked for My 3D Printer
This product was used to convert 24v to 12v for quieter noctua fans on my ender 3. It was easy to set up and worked as expected. This buck converter has less value for the money than other multi packs of more basic designs but is more use friendly for beginners.
Scritto da: Elephants Never Forget
Very useful if you get a working unit.
These are a bit hit and miss depending on the unit you receive. Mine came defective in that the display only partially lit up. Amazon took care of it though, with their excellent customer service. If you get a working unit it's a handy device to have. The voltage adjustment is small and fiddly but I built a wooden box for mine with a knob for adjusting the voltage and several different input and output connectors including a USB output socket for charging phones and power banks. I haven't noticed any voltage spikes on mine and it has been working really well for me. It's the cheapest variable power supply you can get and worth the $10 I paid. I use mine with an 18V solar panel so I can adjust the output voltage to whatever I need for a given device. It will also maintain a set output voltage regardless of fluctuations in the input voltage caused by clouds and varying sunlight levels, so it acts like a charge controller as well as a variable power supply - all in one tiny package.
Scritto da: Marc Mauger
Does what it's supposed to
Does exactly what it's supposed to. I checked the accuracy of the screen against my Multimeter and it checks out. Easy to use and install, so long as you have basic knowledge of electronics. If not, a quick YouTube search can help out.
Scritto da: MrButtons
If an electronics noob can do it, so can you!
First time doing an electronics project. I plugged the wires in, and it came up - what's more to say? It's been perfect to power my Raspberry Pi, and it couldn't be easier to hookup. As long as this review is 5 stars, you'll know it's still alive and kicking!

Σχετικά προϊόντα

Ανακαλύψτε το διεθνές μας δίκτυο

Στέλνουμε σε 28 χώρες, πάνω από 200.000 προϊόντα. Μείνετε ενημερωμένοι, εγγραφείτε στο ενημερωτικό δελτίο.

Array